blow molding machine

Purpose
Fully automatic and electric blow molding machines for high efficient pet bottles production
The blow molding machine is equipped with four or eight blow cavities and a toggle closing unit controlled by electrical servo drives. The blow molding machine is a perfect solution for 0.25 L to 2.5 L bottles, ensuring high and reliable performance. The machine is equipped with a user-friendly touch screen with a graphics interface and an access to heating and blowing parameters, alarms and diagnostic.The machine can be connected directly to the conveyor as the blown bottles are positioned bottom-down.

Features:
Two models: 4 cavity and 8 cavity
Fully electric
Use of servomotors
Highly efficient heating system
Low electricity consumption
Output up to 14.000 B/H
Direct conveying of bottles onto the production line
Precise toggle clumping unit equipped with innovative technologies

Technologies
The blow molding machine was developed due to many years of hard work and hundreds of completed projects. Thanks to this huge experience, our newest blow molding machine is equipped with numerous innovative and user friendly solutions. The most important technologies are:
High Performance Thermal Processor(standard) is a high technology and energy efficient preform heater. The new technology used in this solution enables significant reduction of installed power in the machine and ensures high precision of preform softening process.
Power Wizard(standard) - Pyrometric Temperature Controller is an innovative solution that ensures stable temperature during preform heating process.
Air Recuperation(optional) - a solution designed for air recycling. Thanks to that solution the air demand is much lower.
The Central Lubrication System(standard) allows quick and precise application of grease.
UPS(standard), an emergency power supply for the control unit in case of failure of the regular power supply.
Servomechanism(standard), sometimes shortened to servo, is an automatic device that uses error-sensing negative feedback to correct the performance of a mechanism. The blow molding machines are fully controlled by servomechanisms.
The Detection System(standard) of incorrect blow and bottle defect is an independent controller of the main controller in the electric cabinet of the blow molding machines. The controller has a program designed to detect incorrect blow and reject defective bottles. The program sends a signal by FX3U 16 MT controller to the dumping output and defective bottles are then conveyed to a separate container, so that they are not transported to the bottling line.
The Power Protector(optional) is an autonomous, multi channel control system for regulating heat energy emitted inside the oven of blow molding machine. It controls the amount of electric power supplied to halogen lamps individually for each heating zone or section. Closed loop control algorithms make reheating process insensitive to irregular mains frequency as well as to lamp resistance variation. Thus, the process runs stable and more accurate. Additionally, the Power Protector continuously monitors lamp voltage and current and immediately warns about: dead lamps, suspicious lamp resistance variation (lamp aging), voltage fluctuations in the mains supply. The Power Protector ensures 3-phase symmetrical load and high value of power factor (compared to phase angle controllers). The Power Protector makes the reheating process stable and keeps it fully under control.

Bottle Conveying Machine

Complete bottling lines, engineering, development, design, manufacture of bottling machines for wine, water, oil, juice or spirits.

Full-service millwright company offering custom designs, installation, technical assistance, shop fabrication, field installation, and repair service. Located in Cedar Rapids, Iowa.

Manufacturer of machinery and systems for storage, drying, conveying and blending of pelletized material for delivery to the processing machine.

PET Bottle Conveying Machine

Complete bottling lines, engineering, development, design, manufacture of bottling machines for wine, water, oil, juice or spirits.

Manufacturer of machinery and systems for storage, drying, conveying and blending of pelletized material for delivery to the processing machine.

Designs and supplies conveyer solutions for packaging and bottling industries. Includes features about new products.

Blow Moulding Products

Producer and exporter of commodity moulds, automotive moulds, pipe moulds, baby walker moulds, blowing moulds, industrial products moulds, and electronic moulds.

Injection and blow-moulded plastic products.

Part maker using carbon and aramid fibers. From design to production. Autoclave, RTM, vacuum bag, blow-moulding, cold and hot pressing. [NL]

Preform Moulding Machine

Preformed plywood profiles. Describes its product range of standard and bespoke profiles with application notes.

Manufactures and supplies glass preforms for the electronic and electrical industries.

Specializes in supply of solder preforms in any commercial available alloy. Site provides product, application, and ordering details.